This test is designed to help you assess your knowledge and readiness for the official certification exam.
It covers a wide range of topics, including firearm safety, maintenance, repair, ballistics, and legal regulations.
Each question is multiple-choice, and you will find the correct answers listed at the end of the test.
Good luck, and use this as an opportunity to identify areas where you may need further study!
Earn your accredited, affordable Gunsmith career diploma online with Penn Foster in as little as 3 months!
Certified Professional Gunsmith Practice Test
Question 1 |
To increase accuracy | |
To prevent accidental discharge | |
To reduce recoil | |
To improve durability |
Question 2 |
Caliper | |
Micrometer | |
Bore gauge | |
Feeler gauge |
Question 3 |
Polygonal | |
Button | |
Cut | |
Electrochemical |
Question 4 |
Aluminum | |
Stainless steel | |
Brass | |
Plastic |
Question 5 |
To ignite the primer | |
To remove spent casings from the chamber | |
To feed ammunition into the chamber | |
To stabilize the bullet in flight |
Question 6 |
Centerfire | |
Rimfire | |
Shotshells | |
Blank rounds |
Question 7 |
Lands | |
Rifling | |
Chambers | |
Bore |
Question 8 |
Dirty firing pin | |
Over-lubrication | |
High-quality ammunition | |
Proper maintenance |
Question 9 |
To ensure proper bullet seating | |
To align the barrel with the stock | |
To ensure proper cartridge fit in the chamber | |
To reduce recoil |
Question 10 |
Improved accuracy | |
Case separation | |
Reduced recoil | |
Increased muzzle velocity |
Question 11 |
To ignite the primer | |
To store and feed ammunition | |
To stabilize the bullet | |
To reduce recoil |
Question 12 |
Bolt action | |
Electric action | |
Hydraulic action | |
Pneumatic action |
Question 13 |
Muzzle | |
Chamber | |
Breech | |
Bore |
Question 14 |
Reflex | |
Telescopic | |
Iron | |
All of the above |
Question 15 |
To increase accuracy | |
To reduce recoil | |
To improve durability | |
To enhance concealability |
Question 16 |
Wood | |
Polymer | |
Aluminum | |
All of the above |
Question 17 |
Proofing | |
Cleaning | |
Lubricating | |
Polishing |
Question 18 |
Single-stage | |
Two-stage | |
Set trigger | |
All of the above |
Question 19 |
To reduce muzzle rise | |
To absorb recoil energy | |
To increase accuracy | |
To improve durability |
Question 20 |
Bluing | |
Parkerizing | |
Cerakote | |
All of the above |
Question 21 |
Trajectory | |
Range | |
Windage | |
Elevation |
Question 22 |
Failure to feed | |
Failure to eject | |
Failure to fire | |
All of the above |
Question 23 |
To reduce recoil | |
To cycle the action | |
To increase accuracy | |
To improve durability |
Question 24 |
Full metal jacket | |
Hollow point | |
Soft point | |
All of the above |
Question 25 |
Elevation | |
Windage | |
Zero | |
Parallax |
Question 26 |
Manual safety | |
Grip safety | |
Trigger safety | |
All of the above |
Question 27 |
To ignite the primer | |
To eject the spent casing | |
To feed the ammunition | |
To stabilize the bullet |
Question 28 |
16 inches | |
18 inches | |
20 inches | |
All of the above |
Question 29 |
Zeroing | |
Proofing | |
Headspacing | |
Chambering |
Question 30 |
Recoil spring | |
Hammer spring | |
Magazine spring | |
All of the above |
Question 31 |
To remove spent casings from the chamber | |
To feed ammunition into the chamber | |
To ignite the primer | |
To stabilize the bullet |
Question 32 |
2 pounds | |
4 pounds | |
6 pounds | |
All of the above |
Question 33 |
Bore cleaning | |
Chamber cleaning | |
Action cleaning | |
Stock cleaning |
Question 34 |
Boxer | |
Berdan | |
Both a and b | |
None of the above |
Question 35 |
To hold the cartridge during firing | |
To stabilize the bullet | |
To reduce recoil | |
To increase accuracy |
Question 36 |
Monte Carlo | |
Thumbhole | |
Pistol grip | |
All of the above |
Question 37 |
Zeroing | |
Proofing | |
Headspacing | |
Chambering |
Question 38 |
Carbon steel | |
Stainless steel | |
Both a and b | |
None of the above |
Question 39 |
To lock the cartridge in the chamber | |
To feed ammunition into the chamber | |
To ignite the primer | |
To stabilize the bullet |
Question 40 |
Semi-automatic | |
Pump action | |
Lever action | |
All of the above |
Question 41 |
Grouping | |
Proofing | |
Headspacing | |
Chambering |
Question 42 |
Fixed | |
Hinged | |
Both a and b | |
None of the above |
Question 43 |
To release the hammer or striker | |
To feed ammunition into the chamber | |
To ignite the primer | |
To stabilize the bullet |
Question 44 |
1:7 | |
1:9 | |
1:12 | |
All of the above |
Question 45 |
Trigger job | |
Proofing | |
Headspacing | |
Chambering |
Question 46 |
Recoil spring | |
Hammer spring | |
Magazine spring | |
All of the above |
Question 47 |
To eject the magazine | |
To feed ammunition into the chamber | |
To ignite the primer | |
To stabilize the bullet |
Question 48 |
Recessed | |
Target | |
Both a and b | |
None of the above |
Question 49 |
Stock fitting | |
Proofing | |
Headspacing | |
Chambering |
Question 50 |
Bolt lock | |
Lever lock | |
Both a and b | |
None of the above |
Read the full guide: How to Become a Gunsmith